GIARDINAGGIO 42 GIARDINAGGIO terreni con struttura sabbiosa a quelli pesanti e ricchi di argilla. È importante evitare irrigazioni troppo frequenti e leggere perché così facendo l’apparato radicale rimane superficiale. Si può irrigare in tutte le ore del giorno, però sono da preferirsi le prime ore del mattino e quelle serali. I sistemi di irrigazione sono riconducibili, all’aspersione, con impianti di tipo fisso, semifisso o mobile, e alla microirrigazione o all’irrigazione localizzata, con spruzzatori o con gocciolatori. Quest’ultima consente di realizzare sensibili risparmi idrici ed è ideale per alberi e arbusti. I trattamenti. Sono finalizzati alla difesa della vegetazione dai parassiti, siano animali (insetti) o fungini. I sintomi delle malattie sono evidenti, ma l’importante è riuscire a prevenire gli attacchi attraverso un attento monitoraggio e una buona prevenzione delle cause che possono portare all’insorgere della malattia. La difesa può essere di tipo biologico o con prodotti chimici erogati con macchine irroratrici. Le irroratrici, grazie all’elettronica e ai moderni sensori sono in grado di effettuare una distribuzione uniforme, con perfetta regolazione del prodotto da distribuire, evitando così gli sprechi e l’effetto deriva. La potatura. Riguarda gli arbusti, le siepi e gli alberi del giardino. Per gli arbusti a fioritura invernale-primaverile, le gemme a fiore si formano in estate e la potatura va eseguita al termine della fioritura. Gli arbusti a fioritura estivo-autunnale invece, formano le gemme a fiore in primavera, per cui la potatura si effettua al termine dell’inverno. Gli attrezzi impiegati per la potatura degli arbusti sono le forbici, sia manuali che elettriche a batteria, più pesanti a causa della batteria inserita ma molto meno faticose rispetto alle manuali. Esistono tre tipi di forbici da potatura: a due lame di taglio, ottimali per legni morbidi o freschi; a lama battente su controlama fissa, adatte per legni duri o secchi; a lama passante (bypass) che si comportano come quelle a due lame di taglio e sono adatte sia su legno fresco, sia su legno secco. Per le siepi formali, la potatura viene eseguita per mantenerle nella corretta forma. Per favorire la vegetazione alla base, viene data una forma leggermente trapeziodale, con la base più ampia rispetto alla sommità. La regola generale suggerisce di ridurre l’ampiezza di 10 cm per ogni metro pests, whether animals (insects) or fungi. The symptoms of the disease are obvious, but the important thing is to prevent attacks through careful monitoring and good prevention of the causes that can lead to the onset of the disease. Protection can be biological or chemical, using sprayers. Thanks to electronics and modern sensors, modern sprayers are able to distribute the product evenly, with perfect adjustment of the product to be distributed, thus avoiding waste and drift. Pruning. This applies to shrubs, hedges, and trees in the garden. For shrubs that flower in winter and spring, the flower buds form in summer, and pruning should be done at the end of flowering. Summer-autumn flowering shrubs, on the other hand, form flower buds in spring, so pruning is done at the end of winter. The tools used for pruning shrubs are shears, both manual and battery-powered, which are heavier due to the battery but much less tiring than manual shears. There are three types of pruning shears: two-bladed, ideal for soft or fresh wood; fixed-blade on a fixed counter blade, suitable for hard or dry wood; and bypass blade, which behaves like two-bladed shears and is suitable for both fresh and dry wood. For formal hedges, pruning is carried out to maintain their correct shape. To encourage vegetation at the base, a slightly trapezoidal shape is given, with the base wider than the top. The general rule is to reduce the width by 10 cm for every meter of height. In formal hedges, pruning creates specific architectural shapes. For this purpose, mechanical hedge trimmers are used: first, cutting vertically from bottom to top and vice versa, and then cutting horizontally at the top. For finishing and trimming, manual or battery-powered shears are used, or manual shears with double elongated blades and long handles. The garden may contain both ornamental and fruit trees. Routine pruning of ornamental trees consists of maintenance work carried out at 1-2-year intervals for formal shapes and at longer intervals for informal shapes. This involves the total or partial removal of overgrown and/or vigorous branches, but for free forms, the focus is on trimming the top and branches and thinning out branches and twigs. The tendency is to perform 'gentle' pruning, consisting solely of trimming. A chainsaw is used to cut overgrown branches, while loppers are used to cut branches with a diameter of 4-5 cm. These are hand tools with a cutting
RkJQdWJsaXNoZXIy NTY4ODI=