n. 10-11/2026 139 EIMA SPECIAL L’alta versatilità dell’andantore ST 920 di ROC di Roberto Bonora Quando si parla di andanatori, la capacità di lavorare con precisione e velocità deve necessariamente andare di pari passo con la possibilità di adattarsi alle diverse situazioni che si incontrano in campo. È proprio su questo principio che nasce ST 920, una macchina ottimizzata rispetto alla serie RT, che introduce un concetto particolarmente interessante: una larghezza di lavoro variabile, unita alla possibilità di decidere durante il lavoro dove depositare il prodotto. Composto da due elementi indipendenti da 3,65 metri, l’ST 920 ha una larghezza di lavoro variabile da 7,3 fino a 9,2 metri. Un risultato, questo, ottenuto grazie a un sistema a doppio bilanciere idraulico che permette di modificare la distanza tra i due pick-up anche mentre la macchina è al lavoro. La possibilità di variare l'apertura centrale tra i due elementi non modifica soltanto la larghezza di lavoro, ma amplia in maniera significativa le possibilità di gestione dell'andana. Con i pick-up ravvicinati, l’andanatore può scaricare un nastro a destra e uno a sinistra, oppure entrambi sullo stesso lato. Allargando invece i due elementi, l'ST 920 permette di convogliare entrambi i nastri verso il centro oppure di scegliere diverse combinazioni: un nastro al centro e uno a destra o a sinistra, fino alla possibilità di scaricare entrambi i nastri verso l'esterno. La versatilità del modello ST 920 non si limita alla gestione della larghezza. ROC sottolinea che anche il sistema di sospensione è stato sviluppato per garantire un comportamento efficace sia durante il lavoro che nei trasferimenti. Un ulteriore elemento di praticità è la possibilità di lavorare con uno dei due elementi chiuso, offrendo maggiore libertà nei terreni dove non è necessario utilizzare l'intera larghezza dell’attrezzatura. Nonostante una larghezza di lavoro che può arrivare a 9,2 metri, l'ST 920 è progettato per essere richiudibile per il trasferimento su strada, raggiungendo una larghezza di trasporto di 3 metri. by Roberto Bonora When it comes to swathers, the ability to work with precision and speed must necessarily go hand in hand with the ability to adapt to the different situations encountered in the field. This is precisely the principle that led to the creation of the ST 920. The machine has been optimized from the RT series to introduce a particularly interesting concept: a variable working width, combined with the ability to determine during work where to deposit the product. Made up of two independent 3.65 meter elements, the ST 920 has a variable working width from 7.3 to 9.2 meters. This result has been achieved thanks to a double hydraulic balance system that allows the distance between the two pick-ups to be changed even while the vehicle is working. The ability to vary the central opening between the two elements not only changes the working width, but significantly expands the windrow management possibilities. With close-spaced pick-ups, the swather can unload one belt on the right and one on the left, or both on the same side. By widening the two elements, the ST 920 allows both belts to be conveyed towards the center or to choose different combinations: one belt in the center and one on the right or left, up to the possibility of unloading both belts towards the outside. The versatility of the ST 920 model is not limited to width management. ROC emphasizes that the suspension system has also been developed to ensure effective behavior both during work and for road travel. An additional practical element is the ability to work with one of the two elements closed, offering greater freedom on terrains where it is not necessary to use the full width of the equipment. Despite a working width of up to 9.2 meters, the ST 920 is designed to fold for road transport, reaching a transport width of 3 meters. The high versatility of the ROC ST 920 belt merger
RkJQdWJsaXNoZXIy NTY4ODI=