TECNICA 46 TECNICA do di considerare i meri dati “di targa”. Dal controllo puntuale al TPMS. Le applicazioni più evolute non si limitano ad effettuare un calcolo “statico”, ma si interfacciano con gli ormai ampiamente diffusi TPMS (Tyre Presthis case, CTIS systems (Central Tire Inflation System, centralized systems for changing inflation pressure, see box) prove invaluable, as they make these changes possible even while the vehicle is moving. I primi prototipi furono messi a punto già più di 35 anni fa, e oggi il CTIS è di fatto una realtà consolidata. Si tratta di un impianto che permette di variare dal posto di guida la pressione degli pneumatici di trattori, semoventi e rimorchi, anche con i veicoli in movimento. A differenza del TPMS, che si limita a misurare e comunicare pressione e temperatura, il CTIS modifica attivamente la pressione di ciascun pneumatico del mezzo. L’aria, proveniente da un serbatoio mantenuto in pressione da un compressore, dopo essere stata filtrata arriva ad un regolatore di pressione e successivamente alle elettrovalvole. Il collegamento con le ruote avviene mediante raccordi e giunti rotanti sui mozzi; questi ultimi rappresentano i componenti maggiormente critici dell’intero impianto. Valvole di intercettazione e sensori mantengono separati i circuiti e controllano il raggiungimento del valore impostato. La centralina apre le valvole di gonfiaggio o di scarico e verifica la pressione. In cabina, un monitor dedicato (o il terminale ISOBUS) consente di richiamare profili memorizzati, ad esempio “campo”, “strada” o “rimorchio carico”. I sistemi più completi gestiscono infatti anche l’attrezzo trainato, controllano la velocità e segnalano perdite o altre anomalie. Il vantaggio è rendere possibile ed efficace il passaggio fra due condizioni opposte: in campo serve una pressione bassa (entro i limiti tecnicamente ammessi per quel determinato pneumatico), per ampliare l’area di contatto, in modo da massimizzare la capacità di tiro del trattore e limitare il compattamento; su strada sono invece necessari valori più elevati per maggior capacità di carico e stabilità del cantiere ottimizzata, ma soprattutto per limitare l’usura e la resistenza all’avanzamento. I profili non hanno valori standard: devono essere definiti considerando carico reale sugli assali, velocità, misura e tecnologia costruttiva dello pneumatico, nel rispetto delle specifiche del costruttore. Il CTIS non sostituisce quindi la corretta scelta di pneumatici e zavorre, ma consente di applicare con continuità la pressione adatta alla missione di lavoro. Il CTIS (Central Tyre Inflation System) The first prototypes date back more than 35 years, and today CTIS is firmly established in practice. It is a system that allows the tire pressure of tractors, self-propelled machines, and trailers to be varied from the driver’s seat, even with the vehicles moving. Unlike TPMS, which measures and communicates pressure and temperature, CTIS actively changes each tire’s pressure. Air from a tank kept under pressure by a compressor is filtered and then reaches a pressure regulator and, after that, the solenoid valves. The connection to the wheels is made through fittings and rotary unions on the hubs; the latter are the most critical components of the entire system. Shut-off valves and sensors keep the circuits separate and verify that the set value is reached. The control unit opens the inflation or deflation valves and checks the pressure. In the cab, a dedicated monitor (or the ISOBUS terminal) makes it possible to call up stored profiles, such as “field,” “road,” or “loaded trailer.” In fact, the most complete systems also manage the towed implement, monitor speed, and report leaks or other anomalies. The advantage is that it makes the switch between two opposite conditions both possible and effective: in the field, a low pressure is needed (within the technically permitted limits for that particular tire) to enlarge the contact area, so as to maximize the tractor’s pulling capacity and limit compaction; on the road, higher values are needed for greater load capacity and optimized stability of the tractor-implement combination, but above all to limit wear and motion resistance. Profiles have no standard values: they must be defined by considering the real load on the axles, speed, and the size and construction technology of the tire, in compliance with the manufacturer’s specifications. CTIS therefore does not replace the right choice of tires and ballast, but makes it possible to apply the right pressure continuously for the job at hand. Nel CTIS (sinistra, uno schema di massima), i componenti di maggior criticità sono senza dubbio i giunti rotanti collocati sui mozzi (destra), che devono garantire un’efficace tenuta della pressione nelle parti in movimento In CTIS (left, a general layout), the most critical components are undoubtedly the rotary unions located on the hubs (right), which must ensure an effective pressure seal in the moving parts The CTIS (Central Tire Inflation System)
RkJQdWJsaXNoZXIy NTY4ODI=